Hi
I will need some number plates for a GWR kit I have recently purchased.
I am after a product that is up to the standards of a Malcolm Mitchell kit. A search has revealed Fox Transfers, Modelmasters Jackson Evans, Narrowplanet and 247 Developements. I would appreciate peoples views on these products. There used to be a company called CGW nameplates that doesn't to show up now. As I remember it these were highly regarded. Are these still available?
GWR number plates
-
- Posts: 311
- Joined: Tue Oct 01, 2013 10:06 am
Re: GWR 44xx Kits
I have used Narrow Planet who are the only ones to do bespoke number plates to my knowledge. I have also bought from some of the others who have limited choice of numbers which are searchable online.
-
- Posts: 363
- Joined: Sun May 05, 2013 5:23 pm
Re: GWR 44xx Kits
I recently had a whole batch of number plates done by Brian at 247 Developments and they appear to be as good as anyone else's. He waits until he can fill a sheet before getting them etched. One of my requests was for 4409 plates, now added to his list. At the time Narrow Planet were not taking any new commissions.
Phil
Phil
-
- Posts: 1977
- Joined: Wed Jun 23, 2010 1:04 pm
Re: GWR number plates
The Martin Finney d-i-y ones are available from Brassmasters http://www.brassmasters.co.uk/gwr_etched_components.htm.
Regards
Noel
Noel
-
- Posts: 1947
- Joined: Mon Aug 10, 2009 7:49 pm
Re: GWR number plates
I use 247, Fox Transfers and Modelmaster. All are very good but like any etched plates are a trifle on the thin side. I sometimes glue on a shim or styrene backing plate to bulk cab side plates up a bit.
I think CGW retired a while back.
Philip
I think CGW retired a while back.
Philip
-
- Posts: 1977
- Joined: Wed Jun 23, 2010 1:04 pm
Re: GWR number plates
The maximum depth [over beading and numbers] was 3/4 inch, which is just about 10thou in 4mm unless my maths has gone awry.
Regards
Noel
Noel
-
- Posts: 323
- Joined: Sat Jan 02, 2010 5:04 pm
Re: GWR number plates
The measurements I've taken give a depth of 1" over beading and numbers, with the numbers themselves 1/4" high. There is also a bevelled rim around the outside of the plate around 1/2" deep. To my mind the ideal etched plate would be two layers of 0.006"; I'll get round to doing some one day when I finally do a sheet at that thickness. Admitedly the measurements were taken from preserved locos so I don't know how many of the plates were original (if any) but Noel's point about depth is a valid one, plates generally aren't really thick enough. Name plates similarly. This is most apparent to me on plates for the BR standards which were great chunky things.
Justin
Justin
-
- Posts: 374
- Joined: Mon Jul 21, 2008 9:43 am
Re: GWR number plates
By chance, I’ve just seen the 4D Model Shop newsletter that promotes, what is to me, a new technique that may be interesting for anyone prepared to do their own drawings.
https://modelshop.co.uk/Static/WorkShop/Photo-Etching#control
https://modelshop.co.uk/Static/WorkShop/Photo-Etching#control
Regards,
Andrew Nummelin
Andrew Nummelin
-
- Posts: 1977
- Joined: Wed Jun 23, 2010 1:04 pm
Re: GWR number plates
jjnewitt wrote:The measurements I've taken give a depth of 1" over beading and numbers, with the numbers themselves 1/4" high
I was using a diagram in Brian Haresnape's "Railway Liveries", which agrees on the depth of the numbers; it doesn't look like a Swindon Drawing, but the author was generally reliable. The HMRS "Livery Register" also shows 3/4" overall, with numbers and rim 1/4" [which may, of course, be the source of the dimensions on the drawing in "Railway Liveries"]. It is possible that there was a difference in the depth of brass and cast iron number plates, or it might be the difference between originals and reproductions, or just an error in the drawings; I don't know.
Regards
Noel
Noel
-
- Posts: 911
- Joined: Sun Feb 01, 2009 10:16 pm
-
- Posts: 66
- Joined: Mon Mar 09, 2009 3:58 am
Re: GWR number plates
Hi
I have done a few calculations. If we except that number plates are around 0.75 " thick. This would be around 0.75/76.2 = approx 10 thou in 4mm scale.
I have received the thickness' used by various manufacturers and so far I have found the Narrow planet plates is closest at 12 thou. I believe that 247 uses 8 thou. I am getting clarification of this.
I believe therefore that the closest to scale would be best if everything is is equal. So if I can get the number I need I think I will use narrow Planet or 247 developements. Has anybody any thoughts?
I have done a few calculations. If we except that number plates are around 0.75 " thick. This would be around 0.75/76.2 = approx 10 thou in 4mm scale.
I have received the thickness' used by various manufacturers and so far I have found the Narrow planet plates is closest at 12 thou. I believe that 247 uses 8 thou. I am getting clarification of this.
I believe therefore that the closest to scale would be best if everything is is equal. So if I can get the number I need I think I will use narrow Planet or 247 developements. Has anybody any thoughts?
-
- Posts: 1977
- Joined: Wed Jun 23, 2010 1:04 pm
Re: GWR number plates
bordercollie wrote:So if I can get the number I need I think I will use narrow Planet or 247 developements. Has anybody any thoughts?
Only that the overall appearance, font shape and size, and spacing of digits is probably more important to a convincing number plate than a slight inaccuracy in thickness.
Regards
Noel
Noel
-
- Posts: 46
- Joined: Wed Apr 12, 2017 9:20 pm
Re: GWR number plates
Just received Nameplates and Bunker numbers from Narrow Planet, for two Locos currently under construction. They measure 0.16mm in thickness. I'm very happy with them and they will look great on the finished Locos. JPEG attached. No interest, other than a satisfied customer.
You do not have the required permissions to view the files attached to this post.
Who is online
Users browsing this forum: No registered users and 0 guests