Hornby J94
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Hornby J94
Hi a couple of questions regarding the Hornby J94.
The Hornby model has its drive set with left hand leading or atleast the version I have is, and the DJM model appears to have right hand lead, I know a few different companies built the J94s so I was just wondering which is correct or is it both but it depends etc? I did have a search but couldn't find an answer.
The other question is regarding the Alan Gibson conversion set, the axles are different by 0.1mm and that means the Gibson axles don't fit through the axle bearing tube, what's the best way to correct this size error? Reamer, broach or replace with other tubing cut to size. The drive gear being plastic fits with a little help, but the 2 other axles need the bearing tubes. It a substantial size bearing.
Thanks Dave.
The Hornby model has its drive set with left hand leading or atleast the version I have is, and the DJM model appears to have right hand lead, I know a few different companies built the J94s so I was just wondering which is correct or is it both but it depends etc? I did have a search but couldn't find an answer.
The other question is regarding the Alan Gibson conversion set, the axles are different by 0.1mm and that means the Gibson axles don't fit through the axle bearing tube, what's the best way to correct this size error? Reamer, broach or replace with other tubing cut to size. The drive gear being plastic fits with a little help, but the 2 other axles need the bearing tubes. It a substantial size bearing.
Thanks Dave.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 133
- Joined: Wed Apr 11, 2012 4:55 pm
Re: Hornby J94
The copy of Hunslet GA I have, the plan view shows the crank axle, with the R.H big end fully exposed (TDC) the LH big end is trailing at the three o clock position.
The Vulcan foundry drawing shows the same but strangely in the front elevation both coupling rods are shown at the six o clock position. (BTC)
P
The Vulcan foundry drawing shows the same but strangely in the front elevation both coupling rods are shown at the six o clock position. (BTC)
P
-
- Posts: 643
- Joined: Sun Jul 20, 2008 4:24 pm
Re: Hornby J94
dave_long wrote:Hi a couple of questions regarding the Hornby J94.
The Hornby model has its drive set with left hand leading or atleast the version I have is, and the DJM model appears to have right hand lead, I know a few different companies built the J94s so I was just wondering which is correct or is it both but it depends etc? I did have a search but couldn't find an answer.
The other question is regarding the Alan Gibson conversion set, the axles are different by 0.1mm and that means the Gibson axles don't fit through the axle bearing tube, what's the best way to correct this size error? Reamer, broach or replace with other tubing cut to size. The drive gear being plastic fits with a little help, but the 2 other axles need the bearing tubes. It a substantial size bearing.
IMG_20180520_103843.jpg
Thanks Dave.
If the difference is 0.1mm then use a reamer.
regards
Alan
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Porcy, thanks for the info from the hunslet drawings.
Alan.
Yes the original axles are 2.36mm and fit smoothly through the bearing which I've tried to measure and believe it to be 2.40mm, the Gibson axles measure 2.46mm.
Would I need a straight/parallel reamer as the bearing is just under 8mm long? Would a 2.5mm reamer give a true 2.5mm?
Thanks.
Alan.
Yes the original axles are 2.36mm and fit smoothly through the bearing which I've tried to measure and believe it to be 2.40mm, the Gibson axles measure 2.46mm.
Would I need a straight/parallel reamer as the bearing is just under 8mm long? Would a 2.5mm reamer give a true 2.5mm?
Thanks.
-
- Posts: 643
- Joined: Sun Jul 20, 2008 4:24 pm
Re: Hornby J94
dave_long wrote:Porcy, thanks for the info from the hunslet drawings.
Alan.
Yes the original axles are 2.36mm and fit smoothly through the bearing which I've tried to measure and believe it to be 2.40mm, the Gibson axles measure 2.46mm.
Would I need a straight/parallel reamer as the bearing is just under 8mm long? Would a 2.5mm reamer give a true 2.5mm?
Thanks.
It should do as that is what they are made to do. Also a 2.5mm shaft won't fit in a 2.5mm hole so the 0.04mm undersize is needed.
regards
Alan
-
- Posts: 1558
- Joined: Sun Sep 14, 2008 10:25 pm
Re: Hornby J94
When I converted mine around 10 years ago now, I used standard Gibson wheels and no conversion set as far as I remember. Apparently bushes were available for the coupling rods but actual Austerity 0-6-0ST ones were not available so I chose to use WD 2-8-0 ones as they had the same spacing. They look far better than the Hornby ones. Pipework under the cab thinned to allow clearance. Standard Hornby mechanism. It is presently in for a service after failing at Nottingham in March.
Ordsall Road (BR(E)), Forge Mill Sidings (BR(M)), Kirkcliffe Coking Plant (BR(E)), Swanage (BR (S)) and Heaby (LMS/MR). Acquired Thorneywood (GNR). Still trying to "Keep the Balance".
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Hardwicke
The conversion kit really is just a set of wheels and axles at 2.5mm, designed to fit the Hornby bearings but don't quite. Did you not use the axles bearings or did you still drill them out?
The coupling rod for the 2-8-0 I presume being Gibson is jointed on the crankpin? Has that ever given an issue? I'm not upto creating the articulation off the crank pin just yet.
The conversion kit really is just a set of wheels and axles at 2.5mm, designed to fit the Hornby bearings but don't quite. Did you not use the axles bearings or did you still drill them out?
The coupling rod for the 2-8-0 I presume being Gibson is jointed on the crankpin? Has that ever given an issue? I'm not upto creating the articulation off the crank pin just yet.
-
- Forum Team
- Posts: 3923
- Joined: Sun Jun 29, 2008 8:02 pm
Re: Hornby J94
There must be variants of the chassis, mine does not have any such tube bearings.
Regards
Regards
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
I had started to wonder whether Hornby had altered the chassis as I've looked in the usual places and no one had mentioned such issues. Photos below. The gear is fitted to a AG axle, and you can see the Hornby axle with tubular bearing and the bearing in its seating.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Keith.
Did you use the original coupling rods or did you replace them? I've read that some people bush the rods and some that haven't. I am tempted by the WD rods though. But as I have the bushes and rods already I may just solder them up anyway.
Did you use the original coupling rods or did you replace them? I've read that some people bush the rods and some that haven't. I am tempted by the WD rods though. But as I have the bushes and rods already I may just solder them up anyway.
-
- Posts: 2190
- Joined: Wed Jul 30, 2008 5:56 pm
Re: Hornby J94
Do you actually need the bushes at all Dave?
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Jim,
Probably not, the rod bushes are not part of the list of other bits required for the AG conversion set, where they are a requirement if you buy a set for a Bachmann pannier. I hadn't planned on using the bushes for that reason, but I have a set because of a planned pannier tank conversion I haven't done yet.
But after reading a few people's notes on converting the J94 that there was a lot of slop in the rods, I thought perhaps it might be wise. I'll open the crank pin packet tonight and see what the slop is like.
Probably not, the rod bushes are not part of the list of other bits required for the AG conversion set, where they are a requirement if you buy a set for a Bachmann pannier. I hadn't planned on using the bushes for that reason, but I have a set because of a planned pannier tank conversion I haven't done yet.
But after reading a few people's notes on converting the J94 that there was a lot of slop in the rods, I thought perhaps it might be wise. I'll open the crank pin packet tonight and see what the slop is like.
-
- Forum Team
- Posts: 3923
- Joined: Sun Jun 29, 2008 8:02 pm
Re: Hornby J94
dave_long wrote:Keith.
Did you use the original coupling rods or did you replace them? I've read that some people bush the rods and some that haven't. I am tempted by the WD rods though. But as I have the bushes and rods already I may just solder them up anyway.
I fitted replacement rods, don't remember now where they came from.
Just removed the keeper plate to confirm, definitely no such bearings, the spring for the centre axle bears directly on the axle.
Note, cosmetic lead frame on each side to fill the gap behind the wheels and add weight.
Also widened the keeper plate to bring the brake shoes out to the right place, cut in 3 and reconnect with plasticard.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Thanks Keith.
Definitely a change in design then, the spring has gone too, which isn't helpful. The tubular bearing is a friction fit so the chassis block has been altered to accommodate them. Hopefully the reamer will sort the bearing tube.
Definitely a change in design then, the spring has gone too, which isn't helpful. The tubular bearing is a friction fit so the chassis block has been altered to accommodate them. Hopefully the reamer will sort the bearing tube.
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Keith
Did you glue, or tap and screw the lead to the side frames, I've found a source of 1.8mm flashing and thought I'd try this as I have to remove the main weight to fit an RC battery.
Did you glue, or tap and screw the lead to the side frames, I've found a source of 1.8mm flashing and thought I'd try this as I have to remove the main weight to fit an RC battery.
-
- Forum Team
- Posts: 3923
- Joined: Sun Jun 29, 2008 8:02 pm
Re: Hornby J94
Usually I have drilled and tapped the main frame and screwed the lead on, I do remember trying out a glued job but don't remember now which loco it was. I'll have a look for pictures.
No pictures showing that but I've had the wheelsets out to have a look. No screws so that is the one I tried with glue. The lead does need careful fitting around the pick up wipers to avoid any unwanted contact.
Regards
No pictures showing that but I've had the wheelsets out to have a look. No screws so that is the one I tried with glue. The lead does need careful fitting around the pick up wipers to avoid any unwanted contact.
Regards
Last edited by grovenor-2685 on Mon May 28, 2018 9:16 pm, edited 1 time in total.
Reason: Confirmation of glueing added.
Reason: Confirmation of glueing added.
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Well with the tubular bushes sorted, attention turns back to the coupling rods. In the AG price list it doesn't say the J94 requires the coupling rods to have bushes to narrow the hole, unlike it does for the Bachmann pannier.
However in the crankpin instructions, it states both of the following, the coupling rod must be a slack fit over the crankpin bush, but it also states that the coupling rod should be opened out to 1.5mm. But the holes in the J94 rods are 2.5mm. I feel that having an extra 1mm here is probably too much slack and not a good thing? I think I might fit the extra bushes...
However in the crankpin instructions, it states both of the following, the coupling rod must be a slack fit over the crankpin bush, but it also states that the coupling rod should be opened out to 1.5mm. But the holes in the J94 rods are 2.5mm. I feel that having an extra 1mm here is probably too much slack and not a good thing? I think I might fit the extra bushes...
-
- Posts: 1956
- Joined: Mon Aug 10, 2009 7:49 pm
Re: Hornby J94
I think this must be a mistake in the instructions. Mostly Hornby rods have a 2.5mm hole to clear their larger size crankpin, apart from the 08 shunter which has smaller crankpins. The AG conversion bush brings this down to 1.5mm. The AG crankpin is a touch under this diameter, and I always open the hole, once the bush is soldered in, to 1.6mm, which gives a nice running clearance, a little tighter than the engine as supplied, but not too tight. Beware also that holes in RTR coupling rods, even from the same manufacturer, can vary a little, so the AG conversion bush can be a bit sloppy in the hole. In these cases I use some 2.5/1.6mm brass tube to bush the rod.
Philip
Philip
-
- Posts: 65
- Joined: Mon Feb 02, 2009 9:21 pm
Re: Hornby J94
Thanks Philip.
Interesting though on this Hornby coupling rod, the holes on the 1 driving axle are smaller at 2.2mm, seems a lot of effort to go to in the manufacturing process. Annoying that I have to open them out to then bush them to narrow the hole.
Interesting though on this Hornby coupling rod, the holes on the 1 driving axle are smaller at 2.2mm, seems a lot of effort to go to in the manufacturing process. Annoying that I have to open them out to then bush them to narrow the hole.
Who is online
Users browsing this forum: No registered users and 1 guest