Stour Valley Dream - progress on P4 layout

Tell us about your layout, where you put it, how you built it, how you operate it.
User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Stour Valley Dream - progress on P4 layout

Postby barhamd » Sun Nov 11, 2018 5:45 pm

While I've been regularly posting on rmweb about the P4 layout I thought that those here who don't both with that site might like to see progress. I now have the five main baseboards which feature Clare station built and the track down and wired. This weekend I had fun playing trains and produced a quick video on youtube to prove that you can model in Scalefour without trains falling off the track.

A Cravens DMU (Bachmann) arrives from Cambridge.

IMG_6653a.jpg


An E4 and pair of Gresley coaches arrives from Long Melford.

IMG_6656a.jpg




Hope you enjoy it.

If you want more you can always visit the blog at http://www.rmweb.co.uk/community/index.php?/blog/186-fen-end-pits-blog/

David

User avatar
Colin Parks
Posts: 597
Joined: Sun Oct 27, 2013 4:44 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Colin Parks » Sun Nov 11, 2018 6:12 pm

Hello David,

That video has cheered up a wet Sunday afternoon!

All the best,

Colin

Knuckles
Posts: 1181
Joined: Fri Nov 18, 2011 9:15 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Knuckles » Sun Nov 11, 2018 9:55 pm

Aahhhh....recognized. I believe we recently spoke on YouTube. I'm Sparkshot there.

Looking forward to seeing this progress. :)
“He who dares not offend cannot be honest.” Thomas Paine

http://www.shapeways.com/shops/sparksho ... eationsscc
Mostly offering Loco kits & bits in 4mm.
SCC Photon Resin Prints Price list
download/file.php?id=19320

User avatar
Le Corbusier
Posts: 1169
Joined: Wed Feb 11, 2015 3:39 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Le Corbusier » Sun Nov 11, 2018 10:31 pm

great voice over ... loved it :thumb
Tim Lee

User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barhamd » Sun Nov 11, 2018 10:34 pm

Double Aahhhhhhh

Hence the question about radius and potential P4 layouts, as per another thread on here.
I'm dropping down to about 40" at the tightest spots, getting a continuous run in the room which is ~19'x9'

Unlikely to see a Pacific but a 4-6-0 is a possibility.

David

Dave Holt
Posts: 87
Joined: Thu May 28, 2009 9:44 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Dave Holt » Sat Feb 02, 2019 1:19 pm

David.
Providing you allow sufficient side play on the centre drivers and enough sideways movement on the bogie, I don't see any reason why a 4-6-0 cannot traverse a 40" radius curve.
My earlier efforts, including a WD 2-8-0, a Fairburn 2-6-4 tank and a BR Standard 5 4-6-0 were all able to negotiate a 36" reverse curve, with no transition, test track; and that's on flexitrack with no gauge widening.
Limiting issues tend to be bogie wheels rubbing on front steps and loco to tender spacing - I like to keep this to scale, which can cause problems on sharp curves. The step issue can be solved by moving the steps outwards, slightly. If not over done, it's hardly noticeable in the finished model.
Dave.

User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barhamd » Wed Feb 06, 2019 12:24 am

Some further work has resulted in the second line in the fiddle-yard getting wired and the two turnouts at the ends of the cassette roads being worked with servos. I've fitted these with 'Pocket money Kits' controllers from the MERG which cost only around £2.50 each. These just have a 12v input and three trimpots to set the start and stop location of the servo and its speed.

IMG_6826a.jpg


The result is more trains going round and round and there is some more on Youtube to show it works.



I was surprised by the name check in Scalefour News... The honour - I am not worthy

David

User avatar
Mark Tatlow
Posts: 689
Joined: Tue Dec 02, 2008 11:24 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Mark Tatlow » Wed Feb 06, 2019 9:14 am

Satisfying playing trains for the first (or nearly first I appreciate) time isn't it!!

Keep up the good work!
Mark Tatlow

Dave Holt
Posts: 87
Joined: Thu May 28, 2009 9:44 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Dave Holt » Wed Feb 06, 2019 10:28 am

That looks to be going very nicely - congratulations. I do like the weathering on the freight wagons. keep up the good work.
Dave.

User avatar
barrowroad
Posts: 99
Joined: Sun Jul 20, 2008 5:28 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barrowroad » Wed Feb 06, 2019 4:16 pm

Hi Dave, Nice video and good to see the full extent of your layout. You have a steel? locking plate and slide bolt in the corner near the houses - is this home made or a bought in item. The reason I ask is I am looking for something similar to lock and align the lift out section on my layout.

Keep up the good work.

Regards,

Robin

User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barhamd » Wed Feb 06, 2019 6:43 pm

barrowroad wrote:Hi Dave, Nice video and good to see the full extent of your layout. You have a steel? locking plate and slide bolt in the corner near the houses - is this home made or a bought in item. The reason I ask is I am looking for something similar to lock and align the lift out section on my layout.

Keep up the good work.

Regards,

Robin


Hi Robin

I've got a couple of bolt-like alignment dowels, they are just home-made out of K&S tube.
These tend to work ok, the only issue is where I also want the bolt to conduct power, you'd think two concentric sizes of brass tube would conduct electricity but it ain't necessarily so. In those cases I find having a bit of sprung wire against the bolt then helps.

David

User avatar
barrowroad
Posts: 99
Joined: Sun Jul 20, 2008 5:28 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barrowroad » Wed Feb 06, 2019 8:12 pm

Thanks David I thought you may have fabricated them. I did something similar with the fiddle yard on Sheep Pasture. I was hoping you had found some I could buy off the shelf.
Regards,

Robin

User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barhamd » Sat Apr 27, 2019 12:30 am

I thought I'd post a few more pictures as I know not everyone here follows the updates on my rmweb blog.

The first area of countryside now has its first layer of static grass on it. This needs a lot more work to get a variety of textures and colours but it is coming on.

IMG_7004a.jpg


I made the first sections of post and wire fencing, using some laser cut posts and EZ-line.

IMG_7012a.jpg


I added Woodland Scenics 'deep water' to the river and completed the bridge with some 3D printed girders.

IMG_7019a.jpg


I started making little bushes using string, PVA glue and scenic foam.

IMG_7025a.jpg


I've started work on the Colchester-bound platform, lots of laser cut MDF.

IMG_7038a.jpg


So I then sat back and ran a couple of trains just for the fun.

The pickup goods left the layby siding and headed towards Long Melford.

IMG_7046a.jpg


And then 'Eric the E4' arrived with a passenger service to Cambridge.

IMG_7048a.jpg


As always more details on rmweb at https://www.rmweb.co.uk/community/index.php?/blogs/blog/186-fen-end-pits-blog/

David

User avatar
Le Corbusier
Posts: 1169
Joined: Wed Feb 11, 2015 3:39 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Le Corbusier » Wed May 01, 2019 6:55 pm

A great set of progress photos David .... don't frequent RMweb much so thanks for uploading. :thumb Looking forward to watching this progress ;)
Last edited by Le Corbusier on Fri May 03, 2019 9:38 am, edited 1 time in total.
Tim Lee

Knuckles
Posts: 1181
Joined: Fri Nov 18, 2011 9:15 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Knuckles » Fri May 03, 2019 9:03 am

I haven't said much as I got nothing other than 'firework reactions' to contribute but great to see sone greenery on it at last. Looking forward to the next YT update, asuming there will be one. :)
“He who dares not offend cannot be honest.” Thomas Paine

http://www.shapeways.com/shops/sparksho ... eationsscc
Mostly offering Loco kits & bits in 4mm.
SCC Photon Resin Prints Price list
download/file.php?id=19320

User avatar
barhamd
Posts: 98
Joined: Sun Jul 20, 2008 2:45 pm

Re: Stour Valley Dream - progress on P4 layout

Postby barhamd » Tue May 07, 2019 6:05 pm

I just managed to print off and paint a lever frame for my box. It took two goes to get the support structure right so that the levers came out straight but I think the result is not bad.

This was printed on my Anycubic Photon at .05mm layer height.

The route is set for a train from Clare to leave for Cavendish.

IMG_7083a.jpg


I managed to paint the levers (just) - they are damn small!

IMG_7086a.jpg


IMG_7089a.jpg


Now I have to draw up some block and tablet apparatus.

David

Knuckles
Posts: 1181
Joined: Fri Nov 18, 2011 9:15 pm

Re: Stour Valley Dream - progress on P4 layout

Postby Knuckles » Wed May 08, 2019 3:40 pm

They look brilliant.

I love my Photon too. Brilliant bit of kit.

I can imagine those levers being ruddy fragile though. Get em glued in the box quick. :mrgreen:
“He who dares not offend cannot be honest.” Thomas Paine

http://www.shapeways.com/shops/sparksho ... eationsscc
Mostly offering Loco kits & bits in 4mm.
SCC Photon Resin Prints Price list
download/file.php?id=19320


Return to “Layouts and Operations”

Who is online

Users browsing this forum: No registered users and 3 guests