How many polythene bags of wire or metal sections do you have slipping around in a box or drawer? I have a suggestion that will make storage of these bits much easier.
I bought some plastic tube, in this case 6.4mm x 0.7mm wall and 375mm long. It works out at about 90p a length and will last you a modelling lifetime.
To fit my drawer and the length of metal, I cut the tubes to 330mm - it is not critical but uniformity makes life easier - then pushed a pin 2 to 3mm from one end, right through the middle of both walls and put a decent blob of epoxy in the same end to go round the pin. The pin is 'belt & braces' in case any rod goes in a bit hard and knocks the epoxy out. I made several tubes and stood them upright on a piece thick polythene (firm base, in this case a bit of glass).
I held them in place against my toolbox using some blu-tack at the top.
When the epoxy had dried, I trimmed off the surplus and gently filed the pin back until it was flush, . . .
. . . labelled the open end with an indelible marker pen, . . .
. . . filled them with the appropriate material and put the tubes in to the drawer.
Storing straight things
-
- Posts: 1521
- Joined: Sun Jul 20, 2008 5:30 pm
Storing straight things
You do not have the required permissions to view the files attached to this post.
-
- Forum Team
- Posts: 3049
- Joined: Sun Jul 20, 2008 6:00 pm
Re: Storing straight things
David B wrote:How many polythene bags of wire or metal sections do you have slipping around in a box or drawer? I have a suggestion that will make storage of these bits much easier.
Very neat David. As is your usual style
I continue to keep all of my wire, rod, strip and so on in one of the indispensable Really Useful Boxes. In this case one that seems intended to hold pencils and suchlike. It's about 30 cm long so I don't have to cut down the material at all.
However I've recently discovered that Tesco supply some very useful holders for small drills, wire offcuts and the like:
The plus point is that you can also have some very tasty rice puddings, creme caramel, or tonight's treat - bread and butter pudding.
Cheers
Flymo
You do not have the required permissions to view the files attached to this post.
Beware of Trains - occasional modelling in progress!
www.5522models.co.uk
www.5522models.co.uk
-
- Posts: 86
- Joined: Mon Jun 01, 2015 10:50 pm
Re: Storing straight things
If you store long thin things upright they eventually become long thin things with a a nice curve where the weight pushes down or into the pressure ..
That is where the often recited urban myth that places such as Wickes and BnQ sell crap wood comes from - They dont often, they just store it wrong.
That is where the often recited urban myth that places such as Wickes and BnQ sell crap wood comes from - They dont often, they just store it wrong.
-
- Posts: 1521
- Joined: Sun Jul 20, 2008 5:30 pm
Re: Storing straight things
Neither Paul nor I are storing the wire upright, Mickey.
-
- Forum Team
- Posts: 2428
- Joined: Sun Jul 27, 2008 7:46 am
Re: Storing straight things
mickeym wrote:That is where the often recited urban myth that places such as Wickes and BnQ sell crap wood comes from - They dont often, they just store it wrong.
In fact if you go to a proper timber yard you will find the timber is stored near vertically - a slight angle just to stop it falling over. I bought three 4 metre lengths of 50mm x 25mm planed recently which was very straight.
Terry Bendall
-
- Posts: 86
- Joined: Mon Jun 01, 2015 10:50 pm
Re: Storing straight things
I do go to proper timber yards several times a week, to buy timber (preferably straight)
I think my next layout sub frame will be built of dried out "tanalised wood" - its cheap as chips and straight - or at least it doesn't go anywhere when in a frame
I was referring to timber stored at an angle - Though I don't think I made it clear enough - Store it on end is no problem, store it at less and it develops a bend especially if there is a knot in the area of the potential bend.
I think my next layout sub frame will be built of dried out "tanalised wood" - its cheap as chips and straight - or at least it doesn't go anywhere when in a frame
I was referring to timber stored at an angle - Though I don't think I made it clear enough - Store it on end is no problem, store it at less and it develops a bend especially if there is a knot in the area of the potential bend.
-
- Posts: 850
- Joined: Fri Jul 25, 2008 12:01 pm
Re: Storing straight things
Interesting David, I'd probably just tape over one end but I know you like to do things properly!
All my long thin things are stood in the tubes you get with malt whisky bottles at the moment, one for metal and one for plastic, still in their individual packets in the case of Gibson straight wire or Evergreen strip. This means that I have to remeasure the odd ones with calipers if I need something specific.
All my long thin things are stood in the tubes you get with malt whisky bottles at the moment, one for metal and one for plastic, still in their individual packets in the case of Gibson straight wire or Evergreen strip. This means that I have to remeasure the odd ones with calipers if I need something specific.
Rod
-
- Posts: 1521
- Joined: Sun Jul 20, 2008 5:30 pm
Re: Storing straight things
Rod Cameron wrote:Interesting David, I'd probably just tape over one end but I know you like to do things properly!
I do, Rod. My way, the wire does not get stuck to the sticky tape covering the bottom of the tube.
Rod Cameron wrote:All my long thin things are stood in the tubes you get with malt whisky bottles at the moment . . .
Would these be some intravenous device . . . or drinking straws?
-
- Posts: 13
- Joined: Sat Jan 02, 2010 8:36 pm
Re: Storing straight things
If, like me, you wear dentures you could use empty Steradent tubes for smaller things. I keep my masonry drills in one and it does the job very well.
Return to “Tools and Techniques”
Who is online
Users browsing this forum: ClaudeBot and 2 guests