OMG! I've just noticed that smilies are available and so have used them to take the sting out of the technical stuff below... LOL
Anyone who’s bought a gearbox over the last 18 months will almost certainly have a new, modified version (Unless it was a SlimLiner or MicroMiser, which are unchanged).
A 23 tooth ‘hybrid’ gear (brass centre, nylon teeth) is now used at the axle and this allows a grubscrew fixing throughout the full range of boxes .
Previously, the Loctite fixing required on the axle gears was the most requested change for the gearboxes and, for many, a major influence in their choice of box . This new gear required a re-design of the boxes (although the range is basically the same ) and this included re-working the boxes, tightening up tolerances and taking care of sideplay within the units to make a more precise job . The 23 tooth (instead of 20) means the old ratios have increased by 12%, so 40:1 becomes 45:1, 54:1 is now 60:1 etc.
The instructions have all been redone in a more user-friendly format. Anyone needing info can, on request via e-mail, view any of the instructions in PDF form.
High Level Gearbox range - improvements
-
- Posts: 54
- Joined: Tue Oct 02, 2012 8:37 am
-
- Posts: 561
- Joined: Thu Dec 31, 2009 4:49 pm
Re: High Level Gearbox range - improvements
Thanks for the info Chris.
Gordon A
Bristol
Gordon A
Bristol
-
- Posts: 1600
- Joined: Wed Feb 11, 2015 3:39 pm
Re: High Level Gearbox range - improvements
Somewhat curious to look at the gearbox I bought at Scaleforum now
Tim Lee
-
- Posts: 54
- Joined: Tue Oct 02, 2012 8:37 am
Re: High Level Gearbox range - improvements
If it was S4um 2017 it'll be one of the new ones.
-
- Posts: 1600
- Joined: Wed Feb 11, 2015 3:39 pm
Re: High Level Gearbox range - improvements
High Level Kits wrote:If it was S4um 2017 it'll be one of the new ones.
Excellent
Tim Lee
-
- Posts: 964
- Joined: Mon Sep 14, 2009 6:09 pm
Re: High Level Gearbox range - improvements
Makes me regret my policy of laying in supplies ahead of need, while I have a bit of spare cash!
Now what to do with my older versions
Now what to do with my older versions
-
- Posts: 1116
- Joined: Mon Jul 21, 2008 7:39 pm
Re: High Level Gearbox range - improvements
Paul Townsend wrote:Makes me regret my policy of laying in supplies ahead of need, while I have a bit of spare cash!
Now what to do with my older versions
Put them on ebay with the heading "This version no longer available". You will probably make a profit
-
- Posts: 964
- Joined: Mon Sep 14, 2009 6:09 pm
Re: High Level Gearbox range - improvements
Jol Wilkinson wrote:Paul Townsend wrote:Makes me regret my policy of laying in supplies ahead of need, while I have a bit of spare cash!
Now what to do with my older versions
Put them on ebay with the heading "This version no longer available". You will probably make a profit
Naughty!
-
- Posts: 1116
- Joined: Mon Jul 21, 2008 7:39 pm
Re: High Level Gearbox range - improvements
Paul,
what's naughty about being truthful?. If someone chooses to pay over the odds because they think they are getting something rare or a good deal, that is down to them.
An eBay "trader" told me that he relied on the ignorance or stupidity of buyers to pay more than the price of a newer version of the kits he was selling.
Caveat Emptor.
Jol
what's naughty about being truthful?. If someone chooses to pay over the odds because they think they are getting something rare or a good deal, that is down to them.
An eBay "trader" told me that he relied on the ignorance or stupidity of buyers to pay more than the price of a newer version of the kits he was selling.
Caveat Emptor.
Jol
-
- Posts: 54
- Joined: Tue Oct 02, 2012 8:37 am
J50 Chassis
I’m designing a chassis to go under the Hornby J50 at the request of some P4 modellers. The brief is CSB suspension and removable wheelsets (in other words the springs) and the rest as per the usual High Level spec.
Because this kit is aimed at a much narrower market (two P4 modellers up to now!!!) it can designed with specific features in mind from the word go. Hornblock cut-outs, for example, can be ready done, saving a fair bit of work. Beams and compensation gubbins can be left out, as can the springs which are normally etched as part of the sideframes.
Up to now, I’ve drawn P4 parts only. I’ve ruled out the OO market altogether as the RTR model (so I’m told) runs fine and so can see no reason why anyone using 16.5 would want a chassis, but I’d be interested to know the views of EM modellers. Would you prefer to re-wheel the existing chassis, or build a new fully-spring one from a kit?...
Because this kit is aimed at a much narrower market (two P4 modellers up to now!!!) it can designed with specific features in mind from the word go. Hornblock cut-outs, for example, can be ready done, saving a fair bit of work. Beams and compensation gubbins can be left out, as can the springs which are normally etched as part of the sideframes.
Up to now, I’ve drawn P4 parts only. I’ve ruled out the OO market altogether as the RTR model (so I’m told) runs fine and so can see no reason why anyone using 16.5 would want a chassis, but I’d be interested to know the views of EM modellers. Would you prefer to re-wheel the existing chassis, or build a new fully-spring one from a kit?...
-
- Posts: 60
- Joined: Tue Jan 30, 2018 11:01 am
Re: High Level Gearbox range - improvements
I know this is a bit late coming, as I have only just read the postings about the old style of High Level gearboxes - of which I have some myself - but can't a brass 1/8" adaptor with a screw in the side be used - from Branchlines or whoever it was that supplied them?
Simply thread both on to a 1/8" aluminium axle jig and solder in place on the final drive gear - which is, as I recall is brass and wide - though a bit wider than most others.
So simply mount on the axle jig again and rub on a second cut file, then a smooth file, keeping the axle at 90 degrees to the file, and reduce the width of the gear. Or, better use a lathe if you have one, or a minidrill.
Mike
Simply thread both on to a 1/8" aluminium axle jig and solder in place on the final drive gear - which is, as I recall is brass and wide - though a bit wider than most others.
So simply mount on the axle jig again and rub on a second cut file, then a smooth file, keeping the axle at 90 degrees to the file, and reduce the width of the gear. Or, better use a lathe if you have one, or a minidrill.
Mike
Return to “Product Information”
Who is online
Users browsing this forum: ClaudeBot, rickvon2 and 2 guests