I would like to source a dozen very small connectors, 2 pin. WL recommended some a while ago but my keyword searches have failed to dig this out.
Anyway, smaller ones than those would be good, current expected is <200mA (Mashima 1224) fully loaded.
The model aircraft people seem to have a good selection but all the adverts are short on detrail, such as actual size.
Can anybody advise?
John
Miniature Connectors
-
- Posts: 809
- Joined: Wed Jul 02, 2008 6:39 pm
Miniature Connectors
Slaving away still on GCR stuff ...
-
- Posts: 2870
- Joined: Tue Jul 29, 2008 4:40 pm
Re: Miniature Connectors
I was going to suggest pin connectors, Maplin part JW59P, but the sockets are not listed.
Tim V
(Not all railways in Somerset went to Dorset)
(Not all railways in Somerset went to Dorset)
Re: Miniature Connectors
How about these?
http://www.expressmodels.co.uk/acatalog ... ctors.html
Connector is 1/8" square, but they're quite pricey.
DT
http://www.expressmodels.co.uk/acatalog ... ctors.html
Connector is 1/8" square, but they're quite pricey.
DT
-
- Posts: 809
- Joined: Wed Jul 02, 2008 6:39 pm
Re: Miniature Connectors
David,
I have bought some of these in the past - but yes, they are a bit pricey, so was looking for an alternative.
John
I have bought some of these in the past - but yes, they are a bit pricey, so was looking for an alternative.
John
Slaving away still on GCR stuff ...
-
- Forum Team
- Posts: 3922
- Joined: Sun Jun 29, 2008 8:02 pm
Re: Miniature Connectors
Try these
http://www.ebay.co.uk/itm/40Pcs-1P-1P-2Pin-Header-2-54mm-Male-to-Female-Dupont-Line-Connector-Wire-Cable-/331202599388?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item4d1d3699dc
or many like them, they fit 2.54mm spacing and you an peel off as many as you need from the ribbon cable.
Keith
http://www.ebay.co.uk/itm/40Pcs-1P-1P-2Pin-Header-2-54mm-Male-to-Female-Dupont-Line-Connector-Wire-Cable-/331202599388?pt=UK_BOI_Electrical_Components_Supplies_ET&hash=item4d1d3699dc
or many like them, they fit 2.54mm spacing and you an peel off as many as you need from the ribbon cable.
Keith
-
- Posts: 1512
- Joined: Sun Jul 20, 2008 5:30 pm
Re: Miniature Connectors
Try these from All Components. I use the 2 pin connector to connect pickups to motor. 95p each. Size ⅜" x 3/16".
-
- Posts: 643
- Joined: Sun Jul 20, 2008 4:24 pm
Re: Miniature Connectors
Similar to Keith's suggestion but just the plugs (you have to buy the inserts as well - available separately).
http://cgi.ebay.com/ws/eBayISAPI.dll?Vi ... OC:GB:3160
regards
Alan
http://cgi.ebay.com/ws/eBayISAPI.dll?Vi ... OC:GB:3160
regards
Alan
-
- Forum Team
- Posts: 3922
- Joined: Sun Jun 29, 2008 8:02 pm
Re: Miniature Connectors
The benefit of the pre-made wires is you get both male and female with wires already attached, no need to solder/crimp the inserts. By using male and female appropriately they can be handed to avoid connecting the wrong way, if you need to you can glue them together in pairs.
Downside is that the wire may not be as flexible as you would like, in which case you are back to self assembly.
There are smaller versions available, 1.27 mm spacing but, so far as I can see the male side always needs fixing to a pcb.
Keith
Downside is that the wire may not be as flexible as you would like, in which case you are back to self assembly.
There are smaller versions available, 1.27 mm spacing but, so far as I can see the male side always needs fixing to a pcb.
Keith
-
- Posts: 2524
- Joined: Sun Jul 20, 2008 3:54 pm
Re: Miniature Connectors
davidb wrote:Try these from All Components. I use the 2 pin connector to connect pickups to motor. 95p each. Size ⅜" x 3/16".
These are the ones I use John
Return to “Product Information”
Who is online
Users browsing this forum: ClaudeBot and 1 guest