SR fence posts
-
- Posts: 578
- Joined: Thu Dec 04, 2008 2:15 pm
SR fence posts
Many of you will remember one of the kindest modellers I had the pleasure to know, one J Douglas Smith. Sadly he is no longer with us.
One of his many articles in the model press was on his SR concrete fence posts (MRJ No 180, 2008)
I acquired a good quantity of these from him ( I believe Slaters did the castings) I am trying to get my hands on more. I wrote to slaters a while ago, and they didn’t seem able to help.
Does anyone have a quantity surplus to their needs, or know if who I can approach to do a run on castings.
The photo below is of some I got from Mr.Smith about 10 years ago.
One of his many articles in the model press was on his SR concrete fence posts (MRJ No 180, 2008)
I acquired a good quantity of these from him ( I believe Slaters did the castings) I am trying to get my hands on more. I wrote to slaters a while ago, and they didn’t seem able to help.
Does anyone have a quantity surplus to their needs, or know if who I can approach to do a run on castings.
The photo below is of some I got from Mr.Smith about 10 years ago.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 850
- Joined: Fri Jul 25, 2008 12:01 pm
Re: SR fence posts
I have quite a few of these but none spare.
At Wells I did speak to Alan of ModelU about them and sent him an example with a view to seeing if he could 3D print them, either off the casting or from the drawings in Southern Nouveau; I haven't heard back but I guess he is inundated with other potential products. Might be worth you dropping him a line though.
At Wells I did speak to Alan of ModelU about them and sent him an example with a view to seeing if he could 3D print them, either off the casting or from the drawings in Southern Nouveau; I haven't heard back but I guess he is inundated with other potential products. Might be worth you dropping him a line though.
Rod
-
- Posts: 128
- Joined: Mon Jul 28, 2008 2:19 pm
Re: SR fence posts
Hi,
I am not sure if it will help, but I could produce white metal castings, using these as masters.
Regards,
Tony.
I am not sure if it will help, but I could produce white metal castings, using these as masters.
Regards,
Tony.
-
- Posts: 645
- Joined: Tue Nov 11, 2008 6:51 pm
Re: SR fence posts
The Kent AG have had some 3D printed for Eridge.
They are on KAG member Mark Leigh’s Shapeways shop https://www.shapeways.com/shops/p4-models under the title Southern Region Lineside Concrete Fencing.
Mark kindly passed on the following info -
“There are different materials that it can be printed in, the default is PA12 so you may need to change the material for the cheaper versatile plastic but I understand that the holes never came out with that material?
There is also an Updated Southern Region Lineside Concrete Fencing.
It is the same as the above but has holes in every post.
There is only one material for that model which is PA12, hopefully so the holes are printed [higher resolution material]”
I intend to purchase some once I’ve calculated what I need
Steve
They are on KAG member Mark Leigh’s Shapeways shop https://www.shapeways.com/shops/p4-models under the title Southern Region Lineside Concrete Fencing.
Mark kindly passed on the following info -
“There are different materials that it can be printed in, the default is PA12 so you may need to change the material for the cheaper versatile plastic but I understand that the holes never came out with that material?
There is also an Updated Southern Region Lineside Concrete Fencing.
It is the same as the above but has holes in every post.
There is only one material for that model which is PA12, hopefully so the holes are printed [higher resolution material]”
I intend to purchase some once I’ve calculated what I need
![Thumb Up :thumb](./images/smilies/icon_e_thumbup.png)
Steve
Steve Carter
-
- Posts: 850
- Joined: Fri Jul 25, 2008 12:01 pm
Re: SR fence posts
Thanks Steve - and I've seen the Eridge posts in situ doh!
Clever bloke that Mark ...
Clever bloke that Mark ...
Rod
-
- Posts: 578
- Joined: Thu Dec 04, 2008 2:15 pm
Re: SR fence posts
Thanks Steve - those look very good!
How does the plastic hold up? (Some of the 3D printer plastic seems brittle after a while)
I wonder if they can print them in brass like his ground signal bases?
How does the plastic hold up? (Some of the 3D printer plastic seems brittle after a while)
I wonder if they can print them in brass like his ground signal bases?
-
- Posts: 645
- Joined: Tue Nov 11, 2008 6:51 pm
-
- Posts: 11
- Joined: Wed Nov 22, 2017 9:35 pm
Re: SR fence posts
Hi Guys,
Douglas passed the rights for the fence posts and the disc signals to me.
I am surprised that Slaters said that they knew nothing as we had some correspondence about these just after he died.
Of the fence posts I have few bits of frets, but mainly the centre posts. (Quite a lot of centre posts)
More importantly I have the original tooling.
I have been asked to do another run, but have not had chance to go into this due to work etc. I am also not sure how much demand there is.
As for material, I did consider white-metal as did Doug, however these proved to be too weak so brass is the preferred choice.
It was also suggested that I supply the wire as well. But you have to buy an awful lot of that and also in the right colour. Brown or white?
As there appears to be demand I will put a bit more action into pressing ahead with this.
If anyone wants to express an interest in quantities or colour of wire then let me know.
ps I still have stock of the disc signals
Andy
Douglas passed the rights for the fence posts and the disc signals to me.
I am surprised that Slaters said that they knew nothing as we had some correspondence about these just after he died.
Of the fence posts I have few bits of frets, but mainly the centre posts. (Quite a lot of centre posts)
More importantly I have the original tooling.
I have been asked to do another run, but have not had chance to go into this due to work etc. I am also not sure how much demand there is.
As for material, I did consider white-metal as did Doug, however these proved to be too weak so brass is the preferred choice.
It was also suggested that I supply the wire as well. But you have to buy an awful lot of that and also in the right colour. Brown or white?
As there appears to be demand I will put a bit more action into pressing ahead with this.
If anyone wants to express an interest in quantities or colour of wire then let me know.
ps I still have stock of the disc signals
Andy
-
- Posts: 578
- Joined: Thu Dec 04, 2008 2:15 pm
Re: SR fence posts
Andy - that is excellent news. I have sent you a message (or two)
The ground signals are also lovely little models.....
The ground signals are also lovely little models.....
-
- Posts: 91
- Joined: Wed Jul 23, 2008 2:49 pm
Re: SR fence posts
Here's a pic of some of Mark's excellent fence posts in situ on my shunting plank:
Richard
Richard
You do not have the required permissions to view the files attached to this post.
-
- Posts: 825
- Joined: Fri Jul 15, 2011 11:09 pm
Re: SR fence posts
Before seeing this thread I had never been aware that these fencing components had been manufactured in 4mm scale - obviously I never saw the relevant MRJ article!
If cast in brass then in principle I would be interested in acquiring a quantity, if the price is right. This thread has prompted me to research the fencing for our Burnham layout, leading to the conclusion that we have frightening number of fenceposts to instal. The photograph below suggests that the boundary fencing consisted of posts with the same pitch distance as that between the harps of standard Southern harp-and-panel platform facing; i.e. four feet. Fencing at this pitch extended along the full length of the excursion platform and beyond, yet at the west end of the station there was another length of post-and-wire fencing where the pitch between posts appears to have been between 14'-16'. So there seems to have been quite a lot of variation in the interval between posts. For wire, I would be inclined to use 0.08-0.10 mm monofilament fishing line, or omit the wire altogether.
If cast in brass then in principle I would be interested in acquiring a quantity, if the price is right. This thread has prompted me to research the fencing for our Burnham layout, leading to the conclusion that we have frightening number of fenceposts to instal. The photograph below suggests that the boundary fencing consisted of posts with the same pitch distance as that between the harps of standard Southern harp-and-panel platform facing; i.e. four feet. Fencing at this pitch extended along the full length of the excursion platform and beyond, yet at the west end of the station there was another length of post-and-wire fencing where the pitch between posts appears to have been between 14'-16'. So there seems to have been quite a lot of variation in the interval between posts. For wire, I would be inclined to use 0.08-0.10 mm monofilament fishing line, or omit the wire altogether.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 289
- Joined: Sun Jul 20, 2008 2:45 pm
Re: SR fence posts
I produced some fencing for my ex-GER line using lasercut MDF fence posts and ezyline.
https://www.rmweb.co.uk/community/index.php?/blogs/entry/22158-stour-valley-dream-post-and-wire-fencing/
David
https://www.rmweb.co.uk/community/index.php?/blogs/entry/22158-stour-valley-dream-post-and-wire-fencing/
David
You do not have the required permissions to view the files attached to this post.
-
- Posts: 12
- Joined: Sat Jul 22, 2017 6:05 am
Re: SR fence posts
Hi
As previously mentioned in above posts , i have produced a 3d CAD file which can be printed in a variety of materials.
The original version had witness marks on the posts to assist in positioning the wire between the post as pictured below.
In a silly bid to get totally authentic i then adapted the corner and intermediate post to accept a wire by replacing the witness marks with 0.15mm holes, as shown below.
I'm not sure of my thought process as trying to thread eazyline through the holes would drive you to drink!
The sprues are made up of 2x corner posts , 2 x intermediate posts 2x end posts and 24x bay posts.
There are enough posts to make a run 552mm long ( 138 scale feet) if the nominal 6ft spacing between bay posts is used.
To reduce the cost of printing, i have made these customable by contacting me, i can then upload a file with the quantities you require. Part of the pricing of the printing company is a setup cost which is applied to each item even if it is a multiple purchase of the same item, by redesigning the sprue you only pay one setup cost.
Since the club purchased these, Shapeways have made many advances in the material they offer.
In the "plastic" range the introduction of Acurra Xtreme and Accura 200 which have very good and excellent (respectively) strength properties and good surface finish properties.
EDIT: 08/12/19 - Sorry my mistake Acurra Xtreme and Acurra 200 are not available through the Shapeways shop, they are only available to the designer, this may change with time
The model can also be printed in metals, but the draw back is cost.
As with most models that are printed, one option is to purchase "a master" of the best resolution available and then go down the casting route to offset the cost. This however is extremely time consuming and with investment casting a lot of specialist tooling is needed.
Mark
As previously mentioned in above posts , i have produced a 3d CAD file which can be printed in a variety of materials.
The original version had witness marks on the posts to assist in positioning the wire between the post as pictured below.
In a silly bid to get totally authentic i then adapted the corner and intermediate post to accept a wire by replacing the witness marks with 0.15mm holes, as shown below.
I'm not sure of my thought process as trying to thread eazyline through the holes would drive you to drink!
The sprues are made up of 2x corner posts , 2 x intermediate posts 2x end posts and 24x bay posts.
There are enough posts to make a run 552mm long ( 138 scale feet) if the nominal 6ft spacing between bay posts is used.
To reduce the cost of printing, i have made these customable by contacting me, i can then upload a file with the quantities you require. Part of the pricing of the printing company is a setup cost which is applied to each item even if it is a multiple purchase of the same item, by redesigning the sprue you only pay one setup cost.
Since the club purchased these, Shapeways have made many advances in the material they offer.
In the "plastic" range the introduction of Acurra Xtreme and Accura 200 which have very good and excellent (respectively) strength properties and good surface finish properties.
EDIT: 08/12/19 - Sorry my mistake Acurra Xtreme and Acurra 200 are not available through the Shapeways shop, they are only available to the designer, this may change with time
The model can also be printed in metals, but the draw back is cost.
As with most models that are printed, one option is to purchase "a master" of the best resolution available and then go down the casting route to offset the cost. This however is extremely time consuming and with investment casting a lot of specialist tooling is needed.
Mark
You do not have the required permissions to view the files attached to this post.
Last edited by Mark-Leigh on Sun Dec 08, 2019 5:11 am, edited 1 time in total.
-
- Forum Team
- Posts: 2427
- Joined: Sun Jul 27, 2008 7:46 am
Re: SR fence posts
Mark-Leigh wrote:I'm not sure of my thought process as trying to thread eazyline through the holes would drive you to drink
When I have wanted fencing of a similar style,but only a short run I have used 0.3mm brass wire to represent the fence wire used. Overscale of course but it makes threading the wire a lot easier and the end product is more robust. For the useful product that Mark has produced the holes would need to be enlarged.
Terry Bendall
-
- Posts: 11
- Joined: Wed Nov 22, 2017 9:35 pm
Re: SR fence posts
Quite an encouraging response. I shall get onto this ASAP.
-
- Posts: 11
- Joined: Wed Nov 22, 2017 9:35 pm
Re: SR fence posts
Terry Bendall wrote:Mark-Leigh wrote:I'm not sure of my thought process as trying to thread eazyline through the holes would drive you to drink
When I have wanted fencing of a similar style,but only a short run I have used 0.3mm brass wire to represent the fence wire used. Overscale of course but it makes threading the wire a lot easier and the end product is more robust. For the useful product that Mark has produced the holes would need to be enlarged.
Terry Bendall
Of course you do realise that the wire isn't supposed to go through the holes in the fence posts.
-
- Posts: 578
- Joined: Thu Dec 04, 2008 2:15 pm
Re: SR fence posts
Brightspark wrote:
Of course you do realise that the wire isn't supposed to go through the holes in the fence posts.
I think the wire passes through the tension posts, but not the intermediates.
-
- Posts: 2527
- Joined: Sun Jul 20, 2008 3:54 pm
Re: SR fence posts
Brightspark wrote:Of course you do realise that the wire isn't supposed to go through the holes in the fence posts.
True but as I remember it, the main wire was held in place by a short piece of wire that did pass through the post and was then bent round the main wire either side of post. Modelling that would be fun too.
-
- Posts: 377
- Joined: Sun Jun 17, 2018 8:26 am
Re: SR fence posts
Originally, the wire did go through the intermediate posts but I suspect that problems emerged quite quickly, at a guess slight movement of the wire (wind, temperature changes) caused the galvanising to be abraided and as a result the wire rusted quickly. Later installations, early/mid-1930s onwards perhaps, had the intermediate posts turned so that the holes were orthogonal to the track and a split-pin like arrangement was used to hold the wires close to, but not touching, the post. With this arrangement the wires always ran on the side of the posts furthest from the track so that beasts leaning against the wire wouldn't pull the fixing out of the posts.
On this last point, it is worth noting that the earlier standard SR "concrete" cattle docks had their timber horizontals fixed to the outside of the posts but that by the early 1930s new installations had them on the inside, doubtless for the same reason.
Finally, when we built Bembridge, half-a-century ago now, there was a short length of post and wire fencing (and a gate) at the front of the layout (which, by chance, were still in situ on the prototype at that time). We discovered by experiment that at normal model viewing distances it wasn't actually possible to see scale size wire so it was omitted, the "split-pin" fixings were effectively modelled though by minuscule ink marks.
On this last point, it is worth noting that the earlier standard SR "concrete" cattle docks had their timber horizontals fixed to the outside of the posts but that by the early 1930s new installations had them on the inside, doubtless for the same reason.
Finally, when we built Bembridge, half-a-century ago now, there was a short length of post and wire fencing (and a gate) at the front of the layout (which, by chance, were still in situ on the prototype at that time). We discovered by experiment that at normal model viewing distances it wasn't actually possible to see scale size wire so it was omitted, the "split-pin" fixings were effectively modelled though by minuscule ink marks.
-
- Posts: 1554
- Joined: Sun Sep 14, 2008 10:25 pm
Re: SR fence posts
I've been thinking about these posts for Swanage which has the wrong sort (Ratio). How do I get a supply of these (or similar LNER/ER) ones. I'd need enought for about 22 feet length at least.
Ordsall Road (BR(E)), Forge Mill Sidings (BR(M)), Kirkcliffe Coking Plant (BR(E)), Swanage (BR (S)) and Heaby (LMS/MR). Acquired Thorneywood (GNR). Still trying to "Keep the Balance".
-
- Posts: 91
- Joined: Wed Jul 23, 2008 2:49 pm
-
- Posts: 11
- Joined: Wed Nov 22, 2017 9:35 pm
Re: SR fence posts
I now have stock of these.
See MRJ180 for details.
Posts are made from brass which is obviously more robust than plastic. One pair of frets will do a single run of up to five foot. PM me if you are interested.
Andy
See MRJ180 for details.
Posts are made from brass which is obviously more robust than plastic. One pair of frets will do a single run of up to five foot. PM me if you are interested.
Andy
-
- Posts: 1554
- Joined: Sun Sep 14, 2008 10:25 pm
Re: SR fence posts
What is the difference between the fine detail and natural versatile types?
Ordsall Road (BR(E)), Forge Mill Sidings (BR(M)), Kirkcliffe Coking Plant (BR(E)), Swanage (BR (S)) and Heaby (LMS/MR). Acquired Thorneywood (GNR). Still trying to "Keep the Balance".
-
- Posts: 1554
- Joined: Sun Sep 14, 2008 10:25 pm
Re: SR fence posts
I've tried to contact Mark via the Shapeways site but just get an error message.
Frustrating as I would have ordered some if I knew the difference between the materials, other than "better detail"
Frustrating as I would have ordered some if I knew the difference between the materials, other than "better detail"
Ordsall Road (BR(E)), Forge Mill Sidings (BR(M)), Kirkcliffe Coking Plant (BR(E)), Swanage (BR (S)) and Heaby (LMS/MR). Acquired Thorneywood (GNR). Still trying to "Keep the Balance".
-
- Posts: 12
- Joined: Sat Jul 22, 2017 6:05 am
Re: SR fence posts
Hi Hardwicke
Someone has managed to contact me through Shapeways shop.
You can find out all about the Materials used in Shapeways here https://www.shapeways.com/materials
Fine Detail Plastic https://www.shapeways.com/materials/fine-detail-plastic is traditional used for models as it has good surface finish and supports very fine detail as the name suggests.
Versatile Plastic https://www.shapeways.com/materials/versatile-plastic is stronger than Fine Detail Plastic and has a graint surface finish.
In essence Fine detail will give a crisp shape especially at the apex against versatile plastic .
I am led to believe that those on Eridge were printed (by mistake) in versatile plastic. A picture of which is posted above in FCA reply above and also shown below
Mark
Someone has managed to contact me through Shapeways shop.
You can find out all about the Materials used in Shapeways here https://www.shapeways.com/materials
Fine Detail Plastic https://www.shapeways.com/materials/fine-detail-plastic is traditional used for models as it has good surface finish and supports very fine detail as the name suggests.
Versatile Plastic https://www.shapeways.com/materials/versatile-plastic is stronger than Fine Detail Plastic and has a graint surface finish.
In essence Fine detail will give a crisp shape especially at the apex against versatile plastic .
I am led to believe that those on Eridge were printed (by mistake) in versatile plastic. A picture of which is posted above in FCA reply above and also shown below
Mark
You do not have the required permissions to view the files attached to this post.
Return to “Other Buildings and Scenery”
Who is online
Users browsing this forum: ClaudeBot and 0 guests