New Street
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
OK
Last time I post a picture of this - promise!
A spot of work on the path, tiny spots of dark grey depict discarded chewing gum and equally ting spots of beige with an even smaller spot of white give an impression of discarded cigarette butts!
Its a long time since I hand rendered type. Needs a little bit of cleaning up but overall I am pleased with this little scene!
Cheers
Jim
Last time I post a picture of this - promise!
A spot of work on the path, tiny spots of dark grey depict discarded chewing gum and equally ting spots of beige with an even smaller spot of white give an impression of discarded cigarette butts!
Its a long time since I hand rendered type. Needs a little bit of cleaning up but overall I am pleased with this little scene!
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
Fancied a simple quick project but something that fits into the 'out of the ordinary but very ordinary at the same time' folder.
The point of a billboard is to get your attention and most do this quite well, however take away the poster and they kinda disappear into the urban noise. However a normal billboard is just sheets of plywood. Luckily for me the one on the Odeon cinema is a back lit type and I found a picture of it looking pretty derelict with no poster and the innards on show.
So an evening with microstrip and this is the result
Hope you like it
Jim
Fancied a simple quick project but something that fits into the 'out of the ordinary but very ordinary at the same time' folder.
The point of a billboard is to get your attention and most do this quite well, however take away the poster and they kinda disappear into the urban noise. However a normal billboard is just sheets of plywood. Luckily for me the one on the Odeon cinema is a back lit type and I found a picture of it looking pretty derelict with no poster and the innards on show.
So an evening with microstrip and this is the result
Hope you like it
Jim
-
- Posts: 137
- Joined: Mon Jul 21, 2008 10:34 am
Re: New Street progress
jim s-w wrote:OK
Last time I post a picture of this - promise!
A spot of work on the path, tiny spots of dark grey depict discarded chewing gum and equally ting spots of beige with an even smaller spot of white give an impression of discarded cigarette butts!
Its a long time since I hand rendered type. Needs a little bit of cleaning up but overall I am pleased with this little scene!
Cheers
Jim
Next there will be discarded smiths crisp bags and McDonalds foam burger boxes!!!!
maybe even a waste bin not used of course.
very imppresive work Jim.
regards
trev
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi Trev
Litter yes - No bins though thanks to the IRA!
Cheers
Jim
Litter yes - No bins though thanks to the IRA!
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
Been messing around with the plank again!
Also some more experimentation with long exposures and a single white LED
Cheers
Jim
Been messing around with the plank again!
Also some more experimentation with long exposures and a single white LED
Cheers
Jim
-
- Posts: 296
- Joined: Tue Jul 22, 2008 1:15 am
Re: New Street progress
Jim, I love the shot of the class 47, very O. Winston Link, but with a touch of colour... Very realistic, very impressive.
Cheers,
Mark.
"In the end, when all is said and done, more will have been said than done..."
Mark.
"In the end, when all is said and done, more will have been said than done..."
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Thanks Mark
Been pondering the best way to do the pillars on the platforms at the wolves end of the station. There are 8 of them and they are a bit of a weird shape. Drawing on my previous existence as a designer and doing packaging 'nets' I figured a test based on folding them from thickish card was in order.
The pattern is shown at the top and the whole pillar is double layered for strength. The pillar will fit over a wooden pillar that will hold the shopping center in place. The lines are drawn on with a dead biro and the whole pillar sprayed with plasticote suede for the concrete texture.
Also at the wolves end, there is a low platform on the non public side of the dock. Simple enough this one with a base of foamboard and plastic sheet. The checker plate is wills weathered using the salt method.
The walkway features a air pressure outlet similar, but simpler, to the one outside the signal box. At least you will be able to see this one!
Extreme close up - just some 0.4mm wire and some scraps of microstrip.
Cheers
Jim
Been pondering the best way to do the pillars on the platforms at the wolves end of the station. There are 8 of them and they are a bit of a weird shape. Drawing on my previous existence as a designer and doing packaging 'nets' I figured a test based on folding them from thickish card was in order.
The pattern is shown at the top and the whole pillar is double layered for strength. The pillar will fit over a wooden pillar that will hold the shopping center in place. The lines are drawn on with a dead biro and the whole pillar sprayed with plasticote suede for the concrete texture.
Also at the wolves end, there is a low platform on the non public side of the dock. Simple enough this one with a base of foamboard and plastic sheet. The checker plate is wills weathered using the salt method.
The walkway features a air pressure outlet similar, but simpler, to the one outside the signal box. At least you will be able to see this one!
Extreme close up - just some 0.4mm wire and some scraps of microstrip.
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
A few minutes in photoshop and you get the idea!
Appologies to those sick of the sight...
Cheers
Jim
A few minutes in photoshop and you get the idea!
Appologies to those sick of the sight...
Cheers
Jim
-
- Posts: 62
- Joined: Wed Sep 09, 2009 11:14 am
Re: New Street progress
Point heaters too?
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Point controllers I think Steve.
New Street used (still does in places) Westinghouse EP point motors.
I have been busy with the pepper! Using sludgy grey paint and ground pepper to represent the mouldy stuff you get on damp walls. I have also used Klear for a leak that is still wet.
cheers
Jim
New Street used (still does in places) Westinghouse EP point motors.
I have been busy with the pepper! Using sludgy grey paint and ground pepper to represent the mouldy stuff you get on damp walls. I have also used Klear for a leak that is still wet.
cheers
Jim
Last edited by jim s-w on Thu Dec 16, 2010 10:51 pm, edited 1 time in total.
-
- Posts: 884
- Joined: Thu May 21, 2009 8:11 am
Re: New Street progress
Marvellous, Jim.
Make Worcestershire great again.
Build a wall along the Herefordshire border and make them pay for it.
Build a wall along the Herefordshire border and make them pay for it.
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Thanks Ealing
Dont post a lot of piccies of trians, so to redress the balance a bit a few shots. All of these are taken from the back of the layout so represent views you wont see at shows.
50023 at platform 5
155 307 at platform 4
Hey, I didnt say all pics would be of trains. I saw a shot like this on flickr and thought it looked cool so this is my mini-version!
Finally, with nothing suitable in regards to RTP platform lights I have decided to build my own and this is WIP on the first one (not the actual place for it on the layout). There is no detail on the lower section yet but I have an idea for that.
Cheers
Jim
Dont post a lot of piccies of trians, so to redress the balance a bit a few shots. All of these are taken from the back of the layout so represent views you wont see at shows.
50023 at platform 5
155 307 at platform 4
Hey, I didnt say all pics would be of trains. I saw a shot like this on flickr and thought it looked cool so this is my mini-version!
Finally, with nothing suitable in regards to RTP platform lights I have decided to build my own and this is WIP on the first one (not the actual place for it on the layout). There is no detail on the lower section yet but I have an idea for that.
Cheers
Jim
-
- Posts: 546
- Joined: Thu Oct 08, 2009 10:05 pm
Re: New Street progress
Jim,
As I have written elsewhere in the forum, your modelling is inspirational. I am intrigued by your mention of pepper and " the salt method" during weathering detailing. Can you point us to any " How to do it" articles please.
Or maybe write a short piece for Snooze?
Regards
As I have written elsewhere in the forum, your modelling is inspirational. I am intrigued by your mention of pepper and " the salt method" during weathering detailing. Can you point us to any " How to do it" articles please.
Or maybe write a short piece for Snooze?
Regards
LesG
The man who never made a mistake
never made anything useful
The man who never made a mistake
never made anything useful
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Thanks Les
For pepper just sprinkle onto wet paint. You can also add it before the painting stage if you want to by painting liquid poly onto the surface (of plastic) and sprinkling it on. I used to use it for concrete, for rough concrete sprinkle direct. For smooth sprinkle to the side and blow it across the surface as it falls. Dunno where I picked it up from , might have been in the snooze.
For salt its a simple but ingenious method of using salt as a mask - This guy explains (and does) it far better than I can. One difference I made was to use cooking salt as our models are much smaller
http://www.migproductionsforums.com/phpBB3/viewtopic.php?f=5&t=2802
HTH
Jim
HTH
For pepper just sprinkle onto wet paint. You can also add it before the painting stage if you want to by painting liquid poly onto the surface (of plastic) and sprinkling it on. I used to use it for concrete, for rough concrete sprinkle direct. For smooth sprinkle to the side and blow it across the surface as it falls. Dunno where I picked it up from , might have been in the snooze.
For salt its a simple but ingenious method of using salt as a mask - This guy explains (and does) it far better than I can. One difference I made was to use cooking salt as our models are much smaller
http://www.migproductionsforums.com/phpBB3/viewtopic.php?f=5&t=2802
HTH
Jim
HTH
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
Sticking with lamp-posts for a minute. Some of them had boxes on them that I think are phone boxes. For use by the train crew or departures staff I dunno. I had some from a knightwing pack and started off using a couple. However it bugged me a bit and I decided I could do something a bit better from scraps (also fancied doing something a bit fiddly/daft again!)
On the left - Knightwing version. In the middle my version and on the right, if I am making my own why not one with the door left open? the box is shaped from 3mm square strip/
Cheers
Jim
Sticking with lamp-posts for a minute. Some of them had boxes on them that I think are phone boxes. For use by the train crew or departures staff I dunno. I had some from a knightwing pack and started off using a couple. However it bugged me a bit and I decided I could do something a bit better from scraps (also fancied doing something a bit fiddly/daft again!)
On the left - Knightwing version. In the middle my version and on the right, if I am making my own why not one with the door left open? the box is shaped from 3mm square strip/
Cheers
Jim
-
- Forum Team
- Posts: 3033
- Joined: Sun Jul 20, 2008 6:00 pm
Re: New Street progress
jim s-w wrote:
On the left - Knightwing version. In the middle my version and on the right, if I am making my own why not one with the door left open? the box is shaped from 3mm square strip/
Jim,
You are indeed rapidly approaching certifiable. I am only awaiting items 4 and 5 in the sequence:
#4 - as with #3, but the inside hollowed out, and a bakelite receiver resting inside.
#5 - as with #4, but with nothing inside, a piece of wire dangling out of the front, and the receiver on the floor at the bottom of the post where it was ripped out and thrown by the passing Blues fans...
Great modelling, as always
Flymo
Beware of Trains - occasional modelling in progress!
www.5522models.co.uk
www.5522models.co.uk
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Thanks Paul
Been playing with the LED's again but you get the idea...
Cheers
Jim
Been playing with the LED's again but you get the idea...
Cheers
Jim
-
- Posts: 195
- Joined: Sat Nov 29, 2008 12:13 pm
Re: New Street progress
That photo is excellent Jim, really nice.
Regards,
Nick.
Regards,
Nick.
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
Bit different this one. Board 2 from above.
Also I have been meaning to do a portfolio of my favourite pictures. Nothing new I am afraid but you can see which ones made the cut here http://jsmithwright.demonweb.co.uk/portfolio/
Cheers
Jim
Bit different this one. Board 2 from above.
Also I have been meaning to do a portfolio of my favourite pictures. Nothing new I am afraid but you can see which ones made the cut here http://jsmithwright.demonweb.co.uk/portfolio/
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
Its rare that I buy something for the layout that I think "i can just plonk that straight on" but these are just one of those items.
GPO boxes from unit models - see http://www.unitmodels.com/ for more of their relatively unknown stuff.
I fancied something a bit different and inspired by this thread http://www.rmweb.co.uk/community/index.php/topic/26376-the-birmingham-gun-barrel-proof-house-an-elegant-building/page__p__270430__fromsearch__1#entry270430 I decided to have a go at the sculpture above the gateway. The building itself is a long way off yet but this is what I came up with
Using layers of paper and plasticote suede paint. Its 40mm across.
Cheers
Jim
Its rare that I buy something for the layout that I think "i can just plonk that straight on" but these are just one of those items.
GPO boxes from unit models - see http://www.unitmodels.com/ for more of their relatively unknown stuff.
I fancied something a bit different and inspired by this thread http://www.rmweb.co.uk/community/index.php/topic/26376-the-birmingham-gun-barrel-proof-house-an-elegant-building/page__p__270430__fromsearch__1#entry270430 I decided to have a go at the sculpture above the gateway. The building itself is a long way off yet but this is what I came up with
Using layers of paper and plasticote suede paint. Its 40mm across.
Cheers
Jim
-
- Posts: 618
- Joined: Sun Aug 03, 2008 4:51 pm
Re: New Street progress
Jim
More wonderful stuff, where is N St booked for its first exhibition.
MIke
More wonderful stuff, where is N St booked for its first exhibition.
MIke
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi Mike
Its a good 20 years off yet I think. However I do do occasional work in progress demos. More on a possible 2011 outing later in the year.
Cheers
Jim
Its a good 20 years off yet I think. However I do do occasional work in progress demos. More on a possible 2011 outing later in the year.
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
This afternoon I have built a couple of street lamps -
Built from 0.6mm. 1mm and 1.6mm metal tube with the base from 1/8th Plastruct. The head is shaped from microstrip and the access panel from paper.
Regular visitors will know that because the layout is set in the day, I dont need the lights to work however I fancied a working one to match the one above. Of course the finished item had to look identical so -
The inner workings, A surface mount LED soldered to the 0.6mm tube with a single strand of coated wire fed down the middle.
The finished lamp as lit. I am assuming that one lamp has gone a bit wrong and will stay on!
Cheers
Jim
This afternoon I have built a couple of street lamps -
Built from 0.6mm. 1mm and 1.6mm metal tube with the base from 1/8th Plastruct. The head is shaped from microstrip and the access panel from paper.
Regular visitors will know that because the layout is set in the day, I dont need the lights to work however I fancied a working one to match the one above. Of course the finished item had to look identical so -
The inner workings, A surface mount LED soldered to the 0.6mm tube with a single strand of coated wire fed down the middle.
The finished lamp as lit. I am assuming that one lamp has gone a bit wrong and will stay on!
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
Hi All
A few more items of smaller street furniture.
The temporary bus stop uses the middle of an EFE wheel as its base, copying the real things.
Cheers
Jim
A few more items of smaller street furniture.
The temporary bus stop uses the middle of an EFE wheel as its base, copying the real things.
Cheers
Jim
-
- Posts: 2186
- Joined: Wed Jul 30, 2008 5:56 pm
Re: New Street progress
well,
bearing in mind that the lights I remember were orange when starting up and that I wanted a flickery faulty one the plan was to paint the LED with revel clear orange paint. Didn't work too well. Plus I am not sure flooding the LED with paint is a good idea because its now dead! Oops!
Oh well, needed to do more lights anyway so this time I brought an orange surface mount LED some 10K resistors to dim it down and this is what I ended up with.
Cheers
Jim
bearing in mind that the lights I remember were orange when starting up and that I wanted a flickery faulty one the plan was to paint the LED with revel clear orange paint. Didn't work too well. Plus I am not sure flooding the LED with paint is a good idea because its now dead! Oops!
Oh well, needed to do more lights anyway so this time I brought an orange surface mount LED some 10K resistors to dim it down and this is what I ended up with.
Cheers
Jim
Who is online
Users browsing this forum: ClaudeBot and 2 guests