Page 5 of 5

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Wed Aug 20, 2014 1:42 pm
by David Knight
Rob,

Thanks for the pics of your torque reaction link. A solution very elegant in its simplicity. :thumb

Cheers,

David

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Wed Aug 20, 2014 4:10 pm
by RobM
Ian Everett wrote:
I too am really looking forward to seeing Manston in the flesh - I'll be on the stand next door pushing the SGW concept.
(And I'll bring along a few wedges to prevent that massive pile of barrels falling down - I still worry...)


Get too close and you may also just find the second controller in your hand......... ;)

David Knight wrote:Rob,

Thanks for the pics of your torque reaction link. A solution very elegant in its simplicity. :thumb

Cheers,

David


You're welcome.........
R

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Wed Aug 20, 2014 6:26 pm
by Will L
RobM wrote:
Will L wrote:Interesting Rob. Nice new approach that ought to work just as required.

I suppose logically there is a possibility that the strip might bend back or forward if the chassis was putting up a lot of resistance, but at that point I suspect the chassis needs more basic attention than worrying about the reaction link working properly.


In reality the strip does flex slightly and was only fitted for the purpose of testing just the chassis. The design is such that the motor sits snugly on the removable lower boiler section. The space between the top of the motor and the top of the saddle tank is filled with lead so at most there is only about 1mm of movement.


I know there ain't much room in these Highlevel kits above and below the motor but a little over 1mm ought to be enough as that's the normal design movement limit on a CSB. What you are trying to avoid is the motor pressing down, or up, on the chassis/boiler 'cause if it does it affects the vertical movement of the driven axle. While this is obviously true for the natural rise and fall of the horn bocks, it is also true of additional up/down movement at the far end of the motor due to it's tendency to turn round the axle, hence the need for a reaction link. Without a reaction link stiffness in the chassis can result in the chassis hopping as the driven wheel is pushed down when going in one direction, or "lifting a leg" when going in the opposite direction.
If your getting much flexing I'd beef up the link so it doesn't flex.

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Thu Aug 21, 2014 7:36 am
by RobM
Thanks Will, your points noted.
Rob

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Fri Oct 03, 2014 3:43 pm
by RobM
Thank you to all who stopped by and had a chat at Scaleforum. As a first time exhibitor I did not know what to expect but I thoroughly enjoyed myself.
Loco No 1 developed a problem late Saturday afternoon so I was down to 1 loco. It was not until I got home and completely stripped the loco that I found the problem to be one of the front crankpin nuts which had tightened itself. The Loctite I had from the 1980's had failed................although the opposite crankpin is still 'locked'.

#1-stripped.jpg


Whilst stripped down she was cleaned and I was amazed at the amount of muck.
Anyway, reassembled and running sweetly awaiting the next outing.
R

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Fri Oct 03, 2014 4:20 pm
by Tim V
Loctite has a "shelf life", if yours hasn't got a "use by" date, it's already too old!

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Fri Oct 03, 2014 4:52 pm
by Phil O
RobM wrote:Thank you to all who stopped by and had a chat at Scaleforum. As a first time exhibitor I did not know what to expect but I thoroughly enjoyed myself.
Loco No 1 developed a problem late Saturday afternoon so I was down to 1 loco. It was not until I got home and completely stripped the loco that I found the problem to be one of the front crankpin nuts which had tightened itself. The Loctite I had from the 1980's had failed................although the opposite crankpin is still 'locked'.

#1-stripped.jpg


Whilst stripped down she was cleaned and I was amazed at the amount of muck.
Anyway, reassembled and running sweetly awaiting the next outing.
R


Rob

Was this the cause of the fault which developed in one of the DCC controllers whilst you were away from the layout on the Saturday afternoon.

Phil

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Fri Oct 03, 2014 5:01 pm
by RobM
Tim V wrote:Loctite has a "shelf life", if yours hasn't got a "use by" date, it's already too old!

Tim, I've also got a 'use by' date, it has expired, but I still keep going...... ;)
I was aware, I did a test and it did what it said on the tin, thought I'd chance it.........
R
Phil O wrote:
Rob

Was this the cause of the fault which developed in one of the DCC controllers whilst you were away from the layout on the Saturday afternoon.

Phil

I guess the controller was showing an overload because the loco had basically seized.

R

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Tue Oct 07, 2014 2:55 pm
by Phil O
RobM wrote:
I guess the controller was showing an overload because the loco had basically seized.

R


Rob

I hope it is not to serious and is repairable.

Phil

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Wed Oct 08, 2014 6:38 am
by RobM
Phil O wrote:
Rob

I hope it is not to serious and is repairable.

Phil


Phil,
All was sorted on the 3rd Oct.........total strip down, clean and reassembly..........now running as sweetly as before. :thumb
Rob

Re: Manston Brewery - Setts

Posted: Sun Dec 04, 2016 10:12 am
by RobM
From another thread.......
Knuckles wrote:That is truly impressive and psychotic (in a good way) all at once. Would love to see a picture.


manston-setts.jpg


Knuckles wrote:How did your system not melt and shut down. Good whisky and diazipam? :mrgreen:


Set myself a little bit of time each day doing a small area until the patience ran out........
More on back cover of S4 News 192.

Rob

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Mon Dec 05, 2016 12:19 am
by Knuckles
Hats off to you, Rob. It takes proper dedication to do that with individually placed cobbles. Was it really 10,000+? I don't think I could do it with so many. Does look the part though no doubt about it, a d I guess modelling it this way is the most realistic way to go about it seeing as it was how the real ones were done.

Das clay with a squashed paint brush end appeals more to me though as a method. :D

Re: Manston Brewery Ltd - A Brewery Railway

Posted: Mon Dec 05, 2016 7:27 am
by RobM
Knuckles wrote: Was it really 10,000+?

Just out of interest I kept a tally of the number of batches I cast, after 10,000 I stopped counting but was nearing the end. There is quite an area that has setts.

Knuckles wrote:Das clay with a squashed paint brush end appeals more to me though as a method. :D


I had considered scribing or stamping with a shaped paint brush but at the end of the day it was going to take me roughly the same time........
Rob